Перейти к основному содержанию
Вся химия

5.4 Experimental section

Sijbren Otto - Catalysis of Diels-Alder Reactions in Water

Materials

Trans-chalcone (5.4) (mp 57.1 - 57.7 °C) was obtained from Aldrich and recrystallised from ethanol. Cyclopentadiene (5.2) was prepared from its dimer (Merck-Schuchardt) immediately before use. Demineralised water was distilled twice in a quartz distillation unit. Cu(NO3)2·3H2O (Merck), DyCl3·6H2O (Aldrich), KNO3 (Merck), cetyl trimethylammonium bromide (CTAB, Merck), sodium dodecylsulfate (SDS, BDH Chemicals), dodecyl heptaoxyethylene ether (C12E7, Nikko) and ethylenediaminetetraacetic acid tetrasodium salt trihydrate (EDTA, Aldrich) were of the highest purity available. 1,4,7,10-Tetraazacyclododecane (cyclen) has been kindly provided by Erik Keller. Cu(DS)2 and Zn(DS)2 have been prepared following literature procedures70a and were crystallised from water. Compounds 1a-g or 5.1a-g (in the editors’ view) have been prepared by an aldol condensation of the corresponding substituted aldehyde with 2-acetylpyridine as has been described in Chapter 2. 1H-NMR measurements were performed in D2O (99.9% D, Aldrich). Stock solutions of 5.1c and 5.4 were prepared in methanol-d4 (99.8% D, CIL).

Endo-exo ratios

Endo-exo ratios of the micelle-catalysed reactions have been determined by adding 0.25 mmol of 5.1c and 0.5 mmol of 5.2 to a solution of 5 mmol of surfactant and 0.005 mmol of EDTA in 50 ml of water in carefully sealed 50 ml flasks. The solutions were stirred for 7 days at 26 °C and subsequently freeze-dried. The SDS and CTAB containing reaction mixtures were stirred with 100 ml of ether. Filtration and evaporation of the ether afforded the crude product mixtures. Extraction of the Diels-Alder adducts from the freeze-dried reaction mixture containing C12E7 was performed by stirring with 50 ml of pentane. Cooling the solution to -18 °C resulted in precipitation of the surfactant. Filtration and evaporation of the solvent afforded the adduct mixture. Endo-exo ratios were obtained from the crude product mixtures using 1H-NMR as described in Chapter 2.

Kinetic measurements

All kinetic measurements were performed using UV-vis spectroscopy (Perkin Elmer λ2, λ5 or λ12 photospectrometers) as described in Chapter 2.

Conductivity measurements

Conductivity measurements were performed using a Wayne-Kerr Autobalance Universal Bridge B642 fitted with a Philips electrode PW 95121/01. The solution in the cell was stirred magnetically and thermostatted at 25 (±0.1) °C. The surfactant was added from a stock solution in water in portions of 50 µl and the conductivity was measured. Cmcs were obtained from the intersection of the tangents drawn before and after the break in the conductivity versus concentration plot. The degree of counterion binding is taken as one minus the ratio of these tangents.

NMR measurements

Routine spectra were taken on a Varian VXR 200 MHz or Varian VXR 300 MHz spectrometer. The aromatic shift measurements and the paramagnetic relaxation measurements were performed on a Bruker AC 250 MHz spectrometer. Proton chemical shifts were determined relative to the signal of HOD (4.63 ppm). Paramagnetic relaxation times were determined using the inversion recovery experiment. The variable delay times between the 180o and the 90o pulse were chosen so that they cover the relaxation process during the time-span of minimally five times T1. The 10-16 different delay times were in a random order so as to minimise systematic errors that might result from fluctuations of the strength of the magnetic field during the experiment. The delay time between subsequent pulse sequences was at least five times T1. The T1 values were calculated using a least squares fitting procedure available on the Bruker software.

In a typical experiment 5-10 µl of a stock solution of the 5.1 or 5.2 in D2O or CD3OD was added to a 50 mM surfactant solution in D2O, resulting in a concentration of dienophile and diene of 8.0 and 3.0 mM, respectively. After determination of the proton spin-lattice relaxation times, a stock solution of the paramagnetic species in D2O was added and the relaxation time measurements were repeated. For CTAB solutions, [Cu(EDTA)]2−, prepared in situ from Cu(NO3)2·3H2O and 1.2 equivalent of Na4EDTA·3H2O, served as paramagnetic species in 0.4 mM concentration. For measurements on 5.2 in Zn(DS)2 and SDS solutions, Cu(NO3)2 was added, resulting in a 0.2 mM concentration. For measurements on 5.1 in Zn(DS)2, DyCl3·6H2O was added at 0.2 mM concentration. For SDS micelles, three equivalents (relative to Dy3+) of cyclen was added to prevent direct interaction between Dy3+ and the dienophile83.